Search found 26 matches

by Jim likes catwalks
Fri May 17, 2019 9:13 pm
Forum: Drivetrain
Topic: Helicopter noise
Replies: 5
Views: 107

Re: Helicopter noise

My 2007 lasted about two months before the small needle bearing completely fell apart. Finally fixed it and drove three weeks then started ticking really bad in or out of park or neutral I suspect tranny oil pump. Maybe a broken spring. Sad really everything else was working ok. Jim
by Jim likes catwalks
Fri Feb 22, 2019 10:48 pm
Forum: Drivetrain
Topic: so great to be back!
Replies: 10
Views: 230

Re: so great to be back!

If you buy another freestyle I have some spare transmission parts lol
by Jim likes catwalks
Tue Feb 12, 2019 3:37 pm
Forum: Drivetrain
Topic: Shifts hard in Reverse and Drive P0701 Wrench light
Replies: 5
Views: 191

Re: Shifts hard in Reverse and Drive P0701 Wrench light

The valve body can be Re worked but the TCM can only be replaced as far as I know.
by Jim likes catwalks
Tue Feb 12, 2019 8:04 am
Forum: Drivetrain
Topic: Shifts hard in Reverse and Drive P0701 Wrench light
Replies: 5
Views: 191

Re: Shifts hard in Reverse and Drive P0701 Wrench light

Could be mechatronic unit I tried one out of a wrecker transmission I got for some parts and when I installed it that’s what mine did. Really hard engagement but also in limp mode. With my original mechatronic. It would also go into limp mode until oil warmed all the way up then I could clear PO 942...
by Jim likes catwalks
Thu Feb 07, 2019 8:29 pm
Forum: Drivetrain
Topic: CVT "helicopter" noise - input shaft specs
Replies: 6
Views: 190

Re: CVT "helicopter" noise - input shaft specs

Hello again sorry for delay had some cold weather issues and kept forgetting my calipres at work. So the shaft on drive variator that gets chewed up when the infamous needle bearing goes is .6465”. I don’t have my input shaft anymore as I sent it a month ago to a felllow so I can’t tell you the size...
by Jim likes catwalks
Sun Feb 03, 2019 11:06 pm
Forum: Drivetrain
Topic: CVT "helicopter" noise - input shaft specs
Replies: 6
Views: 190

Re: CVT "helicopter" noise - input shaft specs

I will get some measurements tomorrow
by Jim likes catwalks
Sun Feb 03, 2019 5:04 pm
Forum: Drivetrain
Topic: CVT "helicopter" noise - input shaft specs
Replies: 6
Views: 190

Re: CVT "helicopter" noise - input shaft specs

Hi I fixed mine a couple of years ago and can send you some sizes tomorrow if you want. I had a good input shaft that could be measured by guy I sent it to if he hasn’t installed it yet. Let me know I check this a few times a day. Jim in wintry (finally) BC
by Jim likes catwalks
Sun Jan 13, 2019 2:22 pm
Forum: Drivetrain
Topic: Is it necessary to change the filter with CVT fluid change?
Replies: 115
Views: 70121

Re: Is it necessary to change the filter with CVT fluid change?

That’s what my filter looked like at 213000 kms. I also wrecked a torx head was able to just tack a nut on it then it spun off easy enough would suggest using a 3/8 drive torx socket(number 27) with a hammer impact wrench. They will almost always work. Some wratchets can also be hammered on while tu...
by Jim likes catwalks
Tue Jan 08, 2019 9:29 pm
Forum: Drivetrain
Topic: Front Subframe Hole
Replies: 5
Views: 565

Re: Front Subframe Hole

I also had mine off when doing my transmissionrepair and other than the time and having to heat exhaust pipe connector bolts it went fairly well.
by Jim likes catwalks
Tue Jan 08, 2019 9:25 pm
Forum: Drivetrain
Topic: Need advise on tranny
Replies: 6
Views: 173

Re: Need advise on tranny

Has it been going into limp mode ever that is showing wrench light on dash?
by Jim likes catwalks
Tue Jan 08, 2019 12:25 am
Forum: Performance
Topic: Throttle body HELP
Replies: 6
Views: 180

Re: Throttle body HELP

I bought a used but lifetime guaranteed TCM for two hundred US from transmissionelectricstore and got whole mechatronic unit. My car wouldn’t get out of limp mode until transmission oil got up to 180 degrees fit. I bought a Scan tool so I could read oil temp once it got that warm I could clear my co...
by Jim likes catwalks
Mon Jan 07, 2019 10:23 pm
Forum: Performance
Topic: Throttle body HELP
Replies: 6
Views: 180

Re: Throttle body HELP

Hi sounds a bit like mine after fixing helicopter noise(input shaft needle bearing) ended up being mechatronic was not sending temperature data correctly to PCM which was putting it in limp mode until oil warmed up. Is your problem showing wrench light?
by Jim likes catwalks
Tue Jan 01, 2019 2:23 am
Forum: Drivetrain
Topic: RH (Rear) exhaust manifold
Replies: 2
Views: 88

Re: RH (Rear) exhaust manifold

I had to heat mine on catylitic converter assemblies where they attach to pipe coming off exhaust manifold But not the actual exhaust manifold nuts. Din’t Know if that helps. Jim
by Jim likes catwalks
Mon Dec 17, 2018 7:55 am
Forum: Drivetrain
Topic: P0942 and TCM
Replies: 3
Views: 288

Re: P0942 and TCM

I just wish I had figured it out 1 and a half years ago.
by Jim likes catwalks
Sat Dec 15, 2018 9:56 am
Forum: Drivetrain
Topic: P0942 and TCM
Replies: 3
Views: 288

Re: P0942 and TCM

Success I think finally bought a used guaranteed TCM and got the whole Mechatronics swapped it out wrench light gone!!!